1973 Suzuki GT250: Engine and carburettor work

Lots of simple work needed, but this is a placeholder for when I inevitably have to do an engine rebuild

Compression check

Easy check when I first got the bike – hold throttle open and kick the crap out of it to see what compression we have.

DSC_1793

Spark plug leads have to come off.

DSC_1795

Spark plug tool in to remove the spark plugs

DSC_1796

Plugs out, and compression tester along with various adapters. Need M14 adapter for this, but handy to have others.

DSC_1797

Screw the compression tester in nice and tight

DSC_1798

Kick start only means gotta get out the leg

DSC_1799

Throttle cable snapped? No problem, just pull the inner and kick away.

DSC_1800

Left hand carb

DSC_1801

Right hand carb reading

Good enough to use. Old 2 strokes don’t have that much compression, but this is enough to believe it’s ok.

 

Fixing up carbs and manifolds

DSC_1809

Gotta sort out the manifold studs and the like. Two nuts are the secret. Wind on one, then wind a second one onto it.

DSC_1810

Two nuts touching.

To put in the stud, turn the back of the two nuts. Or, turn the front of the two nuts to take the stud out.

DSC_1812

Back off the front nut once you’re ready to remove the nuts.

DSC_1813

Undo the back nut, then you can take off the other one.

With all the studs installed then that’s all good for the carb and carb manifolds to be bolted onto the cylinders.

DSC_1844

Carb gaskets and float valves are pretty useful to stop fuel leaks.

DSC_1897

Bits involved in a carb rebuild. Carb kits are reasonably available in places like ebay or some of them via your Suzuki dealer.

DSC_1899

Main jet – nice and clean. The ones in the bike were a bit blocked, and the carb kit was cheap enough to buy anyway.

DSC_1901

One carb, ready to come apart.

DSC_1908

Float bowl off.

DSC_1910

Float pivot pin out

DSC_1912

Float valve seat.

DSC_1915

Float valve seat unscrewed.

DSC_1916

Main jet out, note the sealing washer.

DSC_1917

Idle air screw ready to be removed.

DSC_1922

Removing the pilot jet.

DSC_1923

New o-ring for the carb to seal against the manifold.

DSC_1925

Throttle and throttle needle

DSC_1926

Throttle needle retaining clip.

DSC_1938

Throttle cable assembly takes a bit of work. Carb cap and return spring all at the ready.

DSC_1939

Cap and retaining arm all in. Spring goes inside the throttle slide.

DSC_1940

Small split pins normally used here, but I went with lockwire for added race.

DSC_1941

With the spring released you can see how it all goes together

DSC_1942

Spin up the lockwire with lockwire pliers.

DSC_1943

Twist the wire around and cut it off. Pretty.

DSC_1944

Throttle cable nipple goes in here.

DSC_1945

Poke the nipple through the hole with the two apertures.

DSC_1945

Nipple through.

DSC_1947

Throttle cable nipple all seated.

DSC_1948

Throttle slide and cable all assembled onto the carb cap.

DSC_1949

Insert the throttle into the carb.

DSC_1950

Too easy!

Fuel tap – bypassing the vacuum system

Fuel tap wasn’t very happy when I bought the bike.

DSC_1790

I grabbed a gasket kit for my fuel tap, part numbers visible in the below pic.

DSC_1843

Even with this done, the vacuum setup wasn’t working and with no diaphragm available, I bypassed it.

DSC_1845

Fuel tap with some fancy new screws after doing the rebuild.

DSC_1847

Front taken off.

DSC_1848

Here’s where the fuel tap part actually controls the flow of fuel.

DSC_1848_annotated

First up I cleaned up the front part of the fuel tap.

DSC_1849

Enter some 1500-2000 grit sand paper.

DSC_1852

Much better!

DSC_1855

Underneath the little fuel strainer/float thing we get this.

DSC_1855_annotated

The carb is permanently on with the vacuum part not working, so what I did was block up one pipe that bypasses the vacuum bit (the prime pipe). Now ON is on, RES is reserve and PRI is off. Easy.

DSC_1927

Bronze block-off pipe whipped up by a guy at work.

DSC_1928

Some fuel safe sealant.

DSC_1929

Add the fuel safe sealant just to make sure all is good.

DSC_1930

Plug in, note the nice tapped thread to make it easier to pull in and out.

DSC_1931

Bypass to vacuum diaphragm now… bypassed.

DSC_1934

PRIME is off position.

DSC_1935

RES is the reserve position.

DSC_1936

… and ON is on. Perfect.

Fuel filters

DSC_1956

DSC_1957

A necessary evil.

Oil pump adjustment

DSC_1953

The third of the three throttle cables goes into this nipple on the oil pump actuating arm.

DSC_1954

Note the arm has some marks on it, this is with the throttle all the way off.

DSC_1955

Full throttle. Actually a little over-adjusted, but this means a bit more oil is going in than needed.

Air filters

A lot of people would maintain that the bike will run better with an airbox hooked up, but be that as it may I’ve gone with pod filters. Nice angled unifilters.

737300_10152157473097754_1065981034_o