1973 Suzuki GT250: Suspension and brake work

The suspension is something you definitely want to get right, and here’s how I did mine.

Forks and shocks

NOS shocks that look pretty – but might not work the best, so we shall see what I do once I ride it, and nice polished forks.

DSC_7372

Rebuilding the forks

DSC_8902

Certainly not all the tools you’ll need, but usually you’ll need some circlip pliers and a rattlegun helps to undo some stuff if the forks are removed.

DSC_8903

Top cap removed. These forks were clearly rusted into the triple clamps but seriously, the wreckers I bought them from didn’t need to munt the top caps getting them out. Grr.

Anyways, getting the cap off can be fraught with danger. Easy to eject it into your face with the force of the preload on the top cap. Rattle gun if the fork is removed to start it off, or bolt it carefully in a vise being careful not to squish or damage the fork slider at all. Finish it off with a breaker bar, with one hand on top to help hold against the preload. If it’s a particularly stiff set of forks (like on modern sportsbike), consider getting a fork compressor to take the load instead.

DSC_8904

Spring out.

With these forks, there’s little documentation on what oil volume/air height to run. In these cases, it’s good to characterise what is in there. Viscosity was pretty similar to automatic transmission fluid (which is what the Haynes manual recommends).

I’ll show you draining the whole fork in a minute, but if you want to characterise the volume well, you need to capture all of the stuff that’ll come off the other components, too.

DSC_8905

Checking the air height.

Air height is the difference between the top of the fork slider and the oil, with the spring removed and the fork slider fully compressed. Most forks are of sufficient diameter you can use a metal ruler to work it out, and there’s even special tools to make it even easier.

Really long screwdrivers make excellent dipsticks though.

DSC_8906

Difficult to make out where the oil is, but it’s only on the tip. Pretty much at 205-206mm air height. No-one knows what it should be, though :). That’s a fairly ‘low’ air height, but they are also small diameter forks where the spring occupies a relatively large volume.

Air height is more critical in modern forks; it controls the compression damping at the bottom of the stroke. Modern bikes specify a volume AND an air height; use the volume to get it mostly right, then get the air height perfect. This is especially critical if you don’t fully disassemble the forks and you end up with a bit of old oil still in there. Adding the volume specified will probably make it too stiff; in rare cases, you can end up with so much oil that with the spring in, the seal is under enormous pressure which is a great way to end up with a leaking fork seal straight after rebuilding your forks.

DSC_8909

Getting the last of the oil out of the fork, now I’ve measured the air height.

DSC_8910

Ventura racks, with a leather jacket and pants to add some protection to the lovely polished fork leg, makes an excellent way to upend a fork and drain it completely.

DSC_8911

I got 190 mL out of the left hand fork and 180 mL out of the right-hand fork. Values for the amount required vary from ~140 to 230 mL; I’ll go with what came out of it to start with and go up if it needs it. It’s slightly easier to accurately add more oil than it is to accurately drain some :).

DSC_8915

The next task is to get out the damping rod (terminology could be wrong). This is the bolt that holds it in place.

DSC_8913

Most of the time, you need an extra long allen headed socket to get these. Tiny forks let you get away with a normal one.

If you don’t have a long allen socket, you can make one out of an allen key and a 6 sided socket of the appropriate size.

Rattle gun to undo this sometimes, or carefully clamp the fork leg. Some bike manufacturers specify red loctite here; somewhat dumb as it isn’t oil safe, but a hit of heat from a small blowtorch and a tap or three with a hammer on the allen headed socket helps to undo any locking compound.

DSC_8917

Bolt out. Note the sealing washer, made of copper. Best if you buy a new one to make sure when you reassemble it won’t leak. In this case there’s not a choice (it’s a stupid size) so I’ll show you how to deal with it so it won’t leak in a bit.

DSC_8918

Fork gaiter off. No tricks here, just prise it up with something soft so as not to chip the alloy etc.

DSC_8919

Dust seal. Not on all forks. Dentist picks help here, but again, be careful not to damage the fork leg especially on old bikes.

DSC_8920

Now we can see the circlip that retains the fork seal. Some bikes just use a slightly weird ring style that comes off with a couple of small screwdrivers; this is a proper internal circlip.

DSC_8921

Decent circlip pliers help a bunch here.

DSC_8923

With the circlip out, use a dentist pick to get the washer that stops you ripping the seal with your circlip pliers. Not all forks have these.

DSC_8924

With the damping rod undone, it’s time to pop the fork seal out. You can use fork seal removal tools or lots of other ways, I tend to use ‘wank’ (best description of the motion 😉 ) the fork slider up a bunch of times to work the fork seal out. Here it’s half out.

DSC_8925

Fully out. Fork slider is now visible.

DSC_8928

Good idea to lay out all of the components in the order they go into the fork. Helps reassembly.

Now comes the tedious part of cleaning everything up. Some pro tips:
* Brake and parts cleaner is good.
* Remove any chips or burrs in the fork slider, especially where the fork slider runs up and down through the seal, with various grades of steel wool. Coare, fine and super fine are usually sufficient.
* Remove rust with rust removal stuff e.g. a rust converter or something like Reducteur.

These forks had a bunch of rust on the slider. None where the slider goes through the seal, but a bunch on the chrome where they met the triple clamps. This still isn’t good, as you can rip the fork seal putting it on over the slider. Took me about an hour with rust converter and steel wool to remove the majority of the rust and polish the fork slider up to the point where it felt mirror smooth.

DSC_8929

It isn’t perfect but you don’t expect that on 40+ year old forks. A whole lot better than how it was, though.

With everything clean, it’s now time to reassemble the fork.

DSC_8931

Damping rod inside the slider. This helps to keep it centralised to line up the bolt at the bottom.

Time to deal with that sealing washer, if it happens to be made of copper and you can’t get a new one. They’re usually cheap, but this one is a strange external diameter (to fit into the fork bottom) that no-one could get me, and it’s NLA from Suzuki.

DSC_8935

Hang the washer on a bit of wire.

DSC_8943

Use a mini blowtorch to heat it up to cherry red. 2nd washer there is from a brake system and is there to show you an unheated copper washer.

Let it air cool. Now it’s annealed and ready to go.

 

Some manufacturers specify some thread locking compound on the damping rod bolt. Not cool if they come loose. At the same time, the locking compound helps to seal the bolt in case the washer seal isn’t perfect. Fork oil leaking out of the bottom sucks a lot, too.

I like to mix it up a little here. Loctite make a great product called master pipe sealant.

DSC_8944

There are various grades, but one is high temperature and resistant to oil, petrol etc. This is great for sealing sump plugs and the like, and beats using teflon tape for plumbing jobs.

DSC_8945

You don’t need much, but it definitely helps. Really good for those who are too lazy to buy new sump plug washers when they change their oil, too. Since it’s a locking compound as well, it helps to make sure you won’t have the plug coming loose either.

DSC_8946

Now we make sure the fork slider is carefully pushed all the way into the fork. Make sure you push in the fork slider guide, too (which is the bit you can see sticking out of the fork leg).

DSC_8948

Fork seal. They usually come with some grease, this is for the inside mostly to make sure it slides nicely down over the slider and doesn’t get stuck on anything and rip (which causes leaking fork seals).

DSC_8949

Fork seal slid amlost down the slider into the fork leg.

DSC_8951

There are proper fork seal drivers which make this easier, but in a pinch some PVC pipe does. Make sure you carefully drive it in nice and straight, and don’t cut into the fork seal.

DSC_8952

Fork seal in, and washer going on.

DSC_8955

Circlip time. I bought new ones; they were cheap from Capital Bearings and one side was completely rusted and destroyed.

DSC_8956

Circlip going in.

DSC_8959

Circlip in and sitting nicely.

DSC_8961

Damping rod completely tightened. Will torque it up once I clean off enough space on the workbench to clamp it down.

At this point, I filled up the forks with 190 mL of 15W fork oil. Arguments vary on what viscosity to use; automatic transmission fluid is specified by the Haynes manual and it’s about 7.5W. Some people even talk of using monograde 30W engine oil as a fork oil to stiffen them up; getting the springing right is, imho, better than just overdamping the fork. We’ll measure the sag and look at different springs once the bike is assembled then play with the oil to get the damping just right once the bike is done.

DSC_8960

Top cap on. Will fully torque it up when the fork is in the triple clamps (easier to hold then).

DSC_8963

Bottom cap with new pretty and shiny nyloc nuts.

DSC_8964

Dust seal mostly down, then I discovered my bit of PVC is just the wrong diameter. Too lazy to go out and buy another, but it’s not important till I’m ready to put the forks back in the bike.

There you go, disassembly and reassembly of the forks.

Fitting a GT380 fork brace to GT250 forks

This fork brace is a GT380 Tarozzi fork brace I bought from Fast From The Past. It isn’t guaranteed to fit a GT250, but the GT380 uses the same fork space, height above the front guard and fork separation. The tops of the forks, however, are different at least for this area, so I had to take that into account. It might work on later (A-B-C) GT250s, though.

Nothing difficult, but the top has an extra lip that needs shaving down. With access to a lathe this is easy to do perfectly but you could do it with a file or a Dremel.

image

Test work with a spare fork lower. Needed to machine up a taper for the bottom and also the top, and spin it between the 4 jaw chuck and the live centre in the tailstock.

image

It spun beautifully once all set up. With that worked out, I could work about shaving the top lip off the good looking forks I have.

01_fork_before

Fork before we do anything with it.

02_removing_fork_cap

Fork cap off. Fancy pants way of doing it.

03_removing_damping_rod_bolt

Damping rod out.

04_removing_fork_studs

The ol’ two-nut-stud-removal method.

05_bronze_in_chuck

Needed to machine up a fork seal puller. This is to thread into the top of the fork tube.

06_bronze_swarf

Nice bit of swarf!

07_fork_seal_puller_bronze_fitting

Puller screwed in. M14 threaded rod on the inside is how it’ll pull.

08_fork_seal_puller

Do up nut and it pulls the fork seal out. Easy. Only needed for really nice and new fork seals that are in there nice and tight.

09_centering_pipe

Setting up some pipe in the 4 jaw and getting it straight.

Only a small bit of runout – mostly due to the paint on the pipe.

Need to cut a nice taper into the pipe to helpfully centre the fork lower.

10_taper_on_pipe

Taper cut. Also had to cut a really nice bit for the live centre for the tailstock which is doubly tapered. One end fits into the live centre, one fits into the damping rod hole. Together it holds it all nice and centred between the chuck and the tailstock.

11_taper_for_live_centre

Tapered bit for the live centre.

12_taper_in_live_centre

This fits into the damping rod bolt hole to centre it at the far end.

13_shaving_fork_top

Here’s the shaving for the lip off the top of the fork lower.

Autofeed makes life easy.

14_fork_top_done

All shaved top. Perfectly centred so it’ll work great with the fork brace.

15_fork_rebuild_essentials

Rebuild forks as per above section. Important to select correct lubrication.

 

Machining fancy fork caps from 6al4v (aerospace grade 5) titanium

Here’s where we do something a bit different. I decided I wanted to play with machining titanium, so I machined up some fork caps from 36 mm round bar 6al4v titanium stock. Lovely.

 

Caliper and master cylinder rebuild

 

Caliper polishing

 

Selecting a master cylinder

One aspect of the GT250 is the brakes can feel a bit wooden where the lever doesn’t move much but you don’t have much leverage over the pads. The solution is to do the opposite of what a lot of people do with brakes and actually go down a bit of master cylinder size, where you trade lever pull for extra hydraulic pressure. Mechanical advantage wins here. In this case, I wanted to drop from a 14 to a 13 mm master cylinder.

Because I’m fancy, I went a 13 mm radial Magura master cylinder.

1799037_10152261026342754_642224515_o

Fancy.

Brake line fun

Routing is important. For the moment, I’m using a HEL replacement brake line to suit a normal GT250. It’s way too long, but a bit of routing makes it work.

IMG_2737

Homemade p-clip.

IMG_2738

Tap a hole into the fork brace and bolt it in.

IMG_2739

Details.

IMG_2740

Mounted up – and looking good.